← All Heating & Cooling Guides
Short answer: The main types of furnaces are gas, oil and electric. Gas furnaces come in single-stage, two-stage and modulating versions and range from about 80% to 98% AFUE efficiency. For most Philadelphia-area homes with gas service, a two-stage condensing gas furnace is a good balance of comfort and cost.
Last updated: November 15, 2026
Shopping for a new furnace means sorting through a lot of jargon: AFUE, single-stage, modulating, condensing. The right choice depends on your fuel, your home and how long you plan to stay in it. This guide explains every common type of furnace in plain English, with an efficiency and cost chart so you can compare them quickly.
Toran Heating & Air Conditioning is a family-owned HVAC company serving Philadelphia, the Main Line, Eastern Montgomery County and Eastern Delaware County. We install and service gas and electric heat in everything from rowhomes to large single-family houses, so the advice below comes from real replacements in real homes.
Call 610-352-6900 Request a free estimate
Jump to: Comparison chart | Quick picks | Types by fuel | Single, two-stage & modulating | Efficiency (AFUE) | Philadelphia homes | How to choose | FAQ
Furnace Comparison Chart: Efficiency, Cost and Lifespan
Here is how the most common furnace types compare. Costs are typical installed ranges and vary with home size, ductwork, venting and brand, so treat them as a starting point, not a quote.
| Furnace type | Typical efficiency (AFUE) | Typical installed cost | Typical lifespan | Best for |
|---|---|---|---|---|
| Gas, standard efficiency | 80% | $3,500 – $5,500 | 15 – 20 years | Lowest upfront cost, simple replacements |
| Gas, high efficiency (condensing) | 90% – 98% | $4,500 – $8,500 | 15 – 20 years | Lower monthly bills, long-term homeowners |
| Gas, modulating | 95% – 98% | $6,000 – $10,000 | 15 – 20 years | Maximum comfort, quiet operation |
| Oil | 80% – 90% | $4,500 – $10,000 | 15 – 25 years | Homes without gas service, or a stepping stone to conversion |
| Electric | ~100% | $2,500 – $5,500 | 20 – 30 years | Homes with no gas line, small spaces, low upfront cost |
Not sure which furnace fits your home? Request a free estimate or call 610-352-6900.
Quick Picks: Which Furnace Is Right for Your Situation?
- Want the lowest upfront price? A standard-efficiency (80% AFUE) single-stage gas furnace.
- Want lower monthly heating bills? A high-efficiency (90%+ AFUE) condensing gas furnace.
- Want the quietest, most even heat? A two-stage or modulating gas furnace with a variable-speed blower.
- Still heating with oil? Ask about an oil-to-gas conversion if gas service is available on your street.
- No gas line and a small home? An electric furnace, or a heat pump system.
- Planning to sell in a few years? A mid-range single-stage or two-stage unit usually makes the most financial sense.
The Furnace Scale: From Basic to Premium
| Basic | Better | Best balance | Premium |
|---|---|---|---|
| 80% single-stage gas | 90%+ single-stage gas | Two-stage condensing gas | Modulating condensing gas |
| Price: $ | Price: $$ | Price: $$$ | Price: $$$$ |
| Lowest cost, most fuel use | Lower monthly bills | Quiet, even heat | Quietest, most precise |
Types of Furnaces by Fuel
Gas Furnaces
Gas is the most common furnace fuel in the Philadelphia area, and for good reason: natural gas is generally less expensive per unit of heat than electricity or oil, and modern gas furnaces are very reliable. They come in standard-efficiency and high-efficiency models and in single-stage, two-stage and modulating versions, which we explain below.
Best for: Homes with natural gas service (see our gas heating equipment). Keep in mind: High-efficiency models vent through PVC and need a condensate drain, which affects installation in some older homes and rowhomes.
Oil Furnaces
Many older homes in the city and on the Main Line were built with oil heat. Oil furnaces produce strong, steady heat and can last a long time with annual cleaning. The tradeoffs are fuel storage (a tank), delivery scheduling and typically higher fuel and maintenance costs than gas.
Best for: Homes without gas service. Worth considering: If natural gas is available on your street, an oil-to-gas conversion often cuts operating costs and removes the tank.
Electric Furnaces
Electric furnaces are the simplest and cheapest to install. They have no flame, no venting and no combustion, and they tend to last a long time. The downside is operating cost: electricity usually costs more than gas for the same amount of heat, so they are best in small homes or where gas is not an option.
Best for: Small spaces and homes with no gas line. Keep in mind: A heat pump can often deliver the same heat for much less electricity.
Single-Stage vs. Two-Stage vs. Modulating Furnaces
“Staging” describes how a furnace controls its heat output. It has a bigger effect on comfort and noise than on efficiency.
| Type | How it works | Comfort and noise | Typical installed cost |
|---|---|---|---|
| Single-stage | On or off at 100% output | Basic; more temperature swings and noise | $3,500 – $5,500 |
| Two-stage | Low (about 60–70%) for mild days, high for cold snaps | Even heat, quieter | $4,500 – $7,500 |
| Modulating | Adjusts output in small increments, often 40–100% | Most even heat, quietest | $6,000 – $10,000 |
Single-Stage Furnaces
A single-stage furnace runs at full blast until your home reaches the set temperature, then shuts off. It is the simplest design, usually the least expensive, and often the easiest to repair. Expect more noticeable on/off cycling and some temperature swings between rooms.
Best for: Budget-conscious replacements, smaller homes, rental properties.
Two-Stage Furnaces
Two-stage furnaces run on a lower setting most of the time and switch to high only when it is very cold. The result is longer, gentler heating cycles, fewer cold spots and less noise. For many homeowners this is the sweet spot between price and comfort.
Best for: Most family homes, especially two-story houses with uneven temperatures.
Modulating Furnaces
Modulating (also called variable-capacity) furnaces fine-tune their output to match the heat your home needs at that moment. They are the quietest and most precise option and pair well with a variable-speed blower. They cost the most upfront and have more electronics, so ask your installer about long-term repair costs and warranty coverage.
Best for: Homeowners who put comfort and quiet first and plan to stay put.
Furnace Efficiency Explained: What AFUE Means
AFUE stands for Annual Fuel Utilization Efficiency. It tells you how much of the fuel you pay for becomes usable heat. A 95% AFUE furnace turns about 95 cents of every fuel dollar into heat, while an 80% furnace turns about 80 cents.
Standard-Efficiency Furnaces (about 80% AFUE)
These non-condensing furnaces vent hot exhaust through a metal flue or chimney. They cost less to buy and install but use more fuel to heat the same space.
High-Efficiency Condensing Furnaces (90% to 98% AFUE)
These extract extra heat from the exhaust, which cools enough to condense. That means PVC venting through a side wall or roof and a drain for the condensate. In exchange you use less fuel, and the higher the AFUE, the faster the added cost pays back. In a cold-weather climate with a long heating season, the payback is usually worth running the numbers.
Note that staging and efficiency are separate. A single-stage furnace can be 96% efficient, and a two-stage furnace can be 80%, so compare both ratings when you shop.
Not Sure You Have a Furnace? Boilers and Heat Pumps
Many Philadelphia-area homes are heated by a boiler with radiators or baseboards, not a furnace with ducts. If you see cast-iron radiators, you likely have a steam or hot-water boiler. Toran services and replaces gas boilers and furnaces, and we can also help you compare a heat pump system if you are weighing your options.
Choosing a Furnace for a Philadelphia or Main Line Home
Philadelphia and the Main Line have some of the oldest and most varied housing in the region, and that changes which furnace makes sense. Here is what we see most often.
Rowhomes and twins
Space is tight and exterior walls are limited, so venting and clearances often decide what you can install. High-efficiency furnaces vent through PVC pipe out a side wall or the roof and need a condensate drain, so the route has to be planned before you pick a model. A site visit shows what is possible.
Homes still heated with oil
Many older homes were converted from coal to oil decades ago. If natural gas runs down your street, an oil-to-gas conversion can remove the tank and lower operating costs. An older chimney may need a stainless steel liner for a standard-efficiency gas unit, while a high-efficiency furnace vents through PVC and does not use the chimney. See our gas heating equipment page for more.
Homes with radiators
If your home has cast-iron radiators, you have a boiler, not a furnace. Switching to forced-air heat means adding ductwork, which brings extra cost and disruption in an older house. Replacing the boiler with a modern one often makes more sense.
Older ductwork
If you do have ducts, decades-old systems are often leaky or undersized for modern equipment, and they can limit comfort no matter which furnace you buy. Ask for a duct inspection when you get a quote.
What our winters mean for your choice
The heating season is long enough for a high-efficiency furnace to pay off over time, but mild enough that a fully modulating unit is not always worth the premium. For many local homes, a two-stage condensing gas furnace is a good balance of comfort and cost.
Ready for a recommendation for your home? See our Philadelphia furnace repair and installation page or call 610-352-6900.
How to Choose the Right Furnace for Your Home
- Start with your fuel. Your available fuel (gas, oil or electric) narrows the field right away.
- Get the size right. A furnace that is too big short-cycles and wears out early. One that is too small can’t keep up. A proper load calculation for your home matters more than the brand name.
- Check your ductwork. Leaky or undersized ducts waste heat and can limit what a new furnace delivers. It is worth inspecting them at replacement time.
- Plan the venting. High-efficiency furnaces need PVC venting and a condensate drain. Older homes and rowhomes sometimes need creative routing.
- Weigh upfront cost against operating cost. The longer you will stay in the home, the more a higher-efficiency furnace makes sense.
- Look at rebates. Utility and manufacturer rebates change often. Ask us what is currently available when we quote your project.
- Compare full installed quotes. Make sure each quote lists the equipment model, efficiency rating, venting, permits, warranty and any ductwork changes.
Ready to compare real quotes? Book a free in-home estimate and we will walk you through the options for your home.
Signs It May Be Time to Replace Your Furnace
- Your furnace is 15 years old or older.
- Repair bills are climbing, or a single repair costs close to half the price of a new unit. Our furnace repair team can tell you which side of that line you are on.
- Heating bills are rising even though your habits have not changed.
- Some rooms are too hot or too cold, or the system is loud.
- You notice a yellow or flickering pilot or burner flame, soot, or unusual smells. Call a professional right away.
If you ever smell gas or suspect a carbon monoxide leak, leave the house and call your gas utility and 911 from outside.
Furnace Types: Frequently Asked Questions
What is the most efficient type of furnace?
A modulating condensing gas furnace is the most efficient type, with ratings up to about 98% AFUE. High-efficiency single-stage and two-stage furnaces can also reach the mid-90s.
Is a two-stage furnace worth the extra cost?
For many homes, yes. Two-stage furnaces typically cost a few hundred to a couple thousand dollars more than comparable single-stage models and deliver quieter operation and more even temperatures. The benefit is mostly comfort, not a big drop in fuel use.
What is the difference between a furnace and a boiler?
A furnace heats air and distributes it through ducts and vents. A boiler heats water or makes steam and sends it to radiators or baseboard units. Which one you have depends on how your home was built.
How long does a furnace last?
Gas furnaces typically last 15 to 20 years, oil furnaces 15 to 25 years and electric furnaces 20 to 30 years, depending on the unit and how well it has been maintained. Yearly tune-ups help.
Which is cheaper to run: gas, oil or electric?
In most of our service area, natural gas is the least expensive to run, followed by oil and then electric resistance heat. Actual costs depend on current energy prices and your equipment’s efficiency.
Can I convert my oil heat to gas?
If gas service is available on your street, usually yes. We perform oil-to-gas conversions, including removing the old tank and installing new gas equipment.
What size furnace do I need?
Size depends on your home’s heat loss, not just square footage: insulation, windows, layout and ductwork all play a part. We recommend a load calculation before choosing a model.
Furnace Installation and Replacement Near You
We install, repair and replace furnaces across Philadelphia, the Main Line, Eastern Montgomery County and Eastern Delaware County, including Bala Cynwyd, Narberth, Merion, Wynnewood, Ardmore, Havertown, Upper Darby, Drexel Hill, Chestnut Hill and neighborhoods throughout Philadelphia.
Get a Free Furnace Estimate from Toran Heating
Not sure which type of furnace fits your home and budget? Our team will look at your current system, ductwork and venting and recommend options that make sense, with clear pricing and no pressure. See what homeowners say on our reviews and testimonials page.

